Conversation

Notices

1. Disinformation Purveyor :verified_think: (thatguyoverthere@shitposter.club)'s status on Tuesday, 07-Nov-2023 20:13:51 JST Disinformation Purveyor :verified_think:
   Well mistakes were made but it's still looking pretty good. I'm about to glue in the blocking I'll attach the top to and then start sorting through boards to find a couple that will work for the top.
   • Disinformation Purveyor :verified_think: (thatguyoverthere@shitposter.club)'s status on Tuesday, 07-Nov-2023 20:42:55 JST Disinformation Purveyor :verified_think:

     in reply to
     This should work
   • Kek Kerel (kekkerel@freespeechextremist.com)'s status on Tuesday, 07-Nov-2023 20:51:45 JST Kek Kerel

     in reply to
     @thatguyoverthere Nice clean work.
     Disinformation Purveyor :verified_think: likes this.
   • Disinformation Purveyor :verified_think: (thatguyoverthere@shitposter.club)'s status on Tuesday, 07-Nov-2023 20:57:14 JST Disinformation Purveyor :verified_think:

     in reply to

     • Kek Kerel
     @kekkerel Thanks. I can notice some mistakes when I look for them, but it's not bad for a piece of dimensional lumber from a big box store that sat in the yard for 3 months getting abused by the elements. The joints are all tight, but I didn't get it quite squared up before the glue dried. It is really only noticeable with a square up close but it's easier to perceive the further away you are. I think where it is going it probably won't matter, but I might try and throw a tensioning rod in the back to pull it back in alignment. I just don't want to put too much stress on the glue joints as I've used no fasteners at all.
   • Disinformation Purveyor :verified_think: (thatguyoverthere@shitposter.club)'s status on Tuesday, 07-Nov-2023 21:24:00 JST Disinformation Purveyor :verified_think:

     in reply to
     Changed my mind. Going with a larger piece.
   • Disinformation Purveyor :verified_think: (thatguyoverthere@shitposter.club)'s status on Tuesday, 07-Nov-2023 21:35:48 JST Disinformation Purveyor :verified_think:

     in reply to
     Here is a mistake that kind of pisses me off. I must have routed the dado a little too far down this leg and it's about an 1/8th of an inch too short. Not a huge deal as I can just shave a little off the other legs to even it up but dayum man what a pain.
   • Disinformation Purveyor :verified_think: (thatguyoverthere@shitposter.club)'s status on Tuesday, 07-Nov-2023 21:39:54 JST Disinformation Purveyor :verified_think:

     in reply to
     Tbh since it's just going in my office I may just shim it in place and call it good.
   • Disinformation Purveyor :verified_think: (thatguyoverthere@shitposter.club)'s status on Tuesday, 07-Nov-2023 21:42:22 JST Disinformation Purveyor :verified_think:

     in reply to
     It just so happens to be a back leg. Fortunate
   • Kek Kerel (kekkerel@freespeechextremist.com)'s status on Tuesday, 07-Nov-2023 23:11:24 JST Kek Kerel

     in reply to
     @thatguyoverthere It's good that you have these considerations for your own work, but I'm sure you're worried without cause. It looks like it will be a lovely bookshelf.
     Disinformation Purveyor :verified_think: likes this.